ods steel

Get Latest PriceE-mail: [email protected]

Apr 01, 2009Temperatures above 700 °C in the He cooled modular divertor concept necessitates the use of ferritic (RAF) ODS steels, which are not limited by a phase transition. Therefore a 13Cr-1W-0.3Ti-0.3Y 2 O 3 ferritic ODS steel is being developed, using an Attritor with varying milling parameters.

Cited by 23Publish Year 2009Author Ch.Ch. Eiselt, M. Klimenkov, R. Lindau, A. MöslangHRTEM Study of Oxide Nanoparticles in Fe-16Cr ODS (steel) Being a solid-state process, friction stir welding does not melt the steel being joined and would therefore allow ODS steels to maintain their properties after fabrication. A number of samples of MA956, embedded with thermocouples to monitor process temperatures, were successfully welded at TWI's Yorkshire Technology Centre.(plate) Characteristic results and prospects of the 13Cr-1W-0.3Ti ods steel(steel) For the past two decades, ODS steels have been studied extensively in the nuclear community and considerable progress has been made. For example, ODS steel tubes usually reveal an anisotropic strength in the hoop and longitudinal directions due to a strongly elongated grain morphology.(plate) Oxide Dispersion-Strengthened (ODS) Steels Part Two ods steel

In this study, the 9Cr-ODS steel with lower effective chromium content was evaluated to understand the corrosion behavior conservatively. As results, the tube-type specimens of the 9Cr-ODS steels suffered severe weight loss owing to active dissolution at the beginning of the immersion test in pure nitric acid solution in the range from 1 to 3.5 M.

ODS-1 Stainless Steel ozone destruct unit(steel) In this work, a high-temperature low-cycle fatigue (LCF) behavior of a newly developed austenitic oxide dispersion strengthened (ODS) steel is investigated. The LCF tests were performed in air at 650 °C under three different strain amplitudes (±0.4, ±0.5, and ±0.7%) with a nominal strain rate of 10 3 s 1. The measured cyclic stress ods steel(plate) Cited by 3Publish Year 2018Author Ankur Chauhan, Dimitri Litvinov, Tim Gräning, Jarir AktaaWelding the unweldable TWI friction stir welds ODS steel ods steel(steel) ODS METAL SHPK, Rahovec. 275 likes 5 talking about this. Steel Wire Nails(plate) ods steel

R & D on ODS steels consists of mainly 3 tasks; (1) ODS steel composition, (2) fabrication technology of ODS steel cladding tube, and joining technology of ODS steel cladding tube. As a result, advanced ODS steel has been developed, and this material was named as the advanced radiation resistant ODS steel

Development of an oxide-dispersion-strengthened steel by ods steel(steel) The material used for this investigation was 16Cr-4Al-2W-0.3Ti-0.3Y 2O 3 (K3) ODS ferritic steel [10]. Details of the fabrication process of the ODS steel s can be found elsewhere [11]. Briefl y, the pre-alloyed powder was first mechanically alloyed with Y 2O 3 powder in an Argon gas atmosphere at room temperature using an attrition type ball mill.(plate) Cited by 3Publish Year 2010Author Luke L. HsiungCorrosion property of 9Cr-ODS steel in nitric acid ods steel(steel) The stainless steel construction ensures it can covert any concentration of ozone into harmless oxygen. The ODS-1 is a quality destruct device, that allows for simple catalyst replacement by removing the end cap and pouring out old media and replacing. Features. 30-SCFH flow at 10% ozone conc. by wt. 99.9% Efficient; Stainless Steel Construction(plate) ODS METAL SHPK - Home Facebook

oxide dispersion strengtheningods alloyoxide dispersion strengthened alloyods bvoxide materialsdispersion strengtheningods coppersteel used in constructionSome results are removed in response to a notice of local law requirement. For more information, please see here.(steel)Oxide Dispersion-Strengthened (ODS) Steels Part I ods steel

Our Factory & Workshop[email protected]

2500mm Steel Plates Production Line

2500mm Steel Plates Production Line

3500mm Steel Plates Production Line

3500mm Steel Plates Production Line

4500mm Steel Plates Production Line

4500mm Steel Plates Production Line

Spiral Welded Pipe Production Line

Spiral Welded Pipe Production Line

1700mm Hot Rolled Coil Production Line

1700mm Hot Rolled Coil Production Line

Deep Processing Center

Deep Processing Center

R & D and Testing Center[email protected]

Technical department

Technical department

Quality Control

Quality Control

100% UT test

100% UT test

50000J DWT TEST

50000J DWT TEST

Impact test

Impact test

Mechanins Lab

Mechanins Lab

Metallurgical Microscope

Metallurgical Microscope

OES Chemical analysis

OES Chemical analysis

X-ray test

X-ray test

Vickers hardness tester

Vickers hardness tester

Get in Touch

Welcome to contact us through online consulting, emails and hotline if you are interested in our company or products. Our staff will reply you within 24 hours.


Contact Us